
                             NOTES FOR DEBIAN USERS
                             ======================


1. AUTOMATIC STARTUP
--------------------

In order to avoid the startup of the firewall on an unconfigured machine,
automatic startup, on boot, is disabled by default. To enable it just edit the
file /etc/default/shorewall6 and set the "startup" variable to 1.


2. CONFIGURATION
----------------

After the installation of the package the configuration directory
/etc/shorewall6/ will remain empty, except for:
   
   1. shorewall6.conf
   2. Makefile

This is intentional because:

   1. there does not exist a sane default configuration 
   2. to avoid dpkg to prompt for upgrade of configuration file on every
      package update

The default upstream configuration files are installed, just as an example, in
/usr/share/shorewall6/configfiles/.

In order to configure a simple firewall you should, at least, set up the
following files:

   1. /etc/shorewall6/interfaces
   2. /etc/shorewall6/policy
   3. /etc/shorewall6/rules
   4. /etc/shorewall6/zones

Default Debian configuration is slightly different from upstream configuration.
The differences are:

   1. IP forwarding is neither enabled nor disabled. It is set to "keep", that
      means that if it is enabled it will remain enabled, and if it is disabled
      it will remain disabled. If you are going to configure your host to act
      as a router take care of this fact. To enable IP forwarding you have to
      set to "on" the IP_FORWARDING variable in /etc/shorewall6/shorewall6.conf
   2. Anti-spoofing kernel protections are enabled, by default, on all
      interfaces. Upstream configuration disables it. To disable it set the
      variable ROUTE_FILTER to "no" in /etc/shorewall6/shorewall6.conf

Other files such as modules, action.* and actions.std, that usually don't need
customization, are installed within /usr/share/shorewall6. Customization can be
done in /etc/shorewall6 as shorewall looks for files in /etc/shorewall6 and
then in /usr/share/shorewall6. If a configuration file is found in
/etc/shorewall6 the one in /usr/share/shorewall6 is ignored.

More information about shorewall configuration can be found in the
shorewall-doc package and on the shorewall website (http://www.shorewall.net).


3. AVOIDING FLOOD (WITH LOGGED TRAFFIC) ON THE CONSOLE
-----------------------------------------------------

Shorewall logs packets using level "info". With the default klogd
configuration these messages are also written on the console, and
when the frequency of logging is high the console becomes unusable. It
is highly recommended to configure klogd in order to prevent that
messages of level "info" are logged on the console. You have two
alternatives:

   1. set KLOGD="-c 5" in /etc/init.d/klogd 
   2. add dmesg -n5 in your /etc/shorewall6/start


5. PPP USERS 
------------

This section replaces old documentation found in
/usr/share/doc/shorewall/README.ppp

If you are running shorewall on a machine with a ppp connection and your
firewall needs to calculate the interface's ip address, the startup can fail.
It can fail because at the time the firewall is started the ppp interface is
not ready yet. For other information about the problem see bugs #175382 and
#234189.

If your ppp connection is configured with /etc/init.d/ppp you must set it up
using /etc/network/interfaces using the PPP method because just the networking
script is run before shorewall. Moreover the interface name must be listed,
using the "wait_interface" keyword, in /etc/default/shorewall6 in order to get
the init script to wait until its ready.

Examples of /etc/default/shorewall6:

   wait_interface="ppp0"

or 

   wait_interface="ppp0 ppp1"

or, if you have defined $PPP in /etc/shorewall6/params
   
   wait_interface=$PPP


 -- Lorenzo Martignoni <martignlo@debian.org>, Thu, 19 Oct 2006 04:21:16 +0200
